View TS51405_4789721.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TS514 / TS514A
Precision Quad Operational Amplifier

Low input offset voltage: 500V max. Low power consumption. Short circuit protection. Low distortion, low noise. High gain-bandwidth product. High channel separation. ESD protection 2kV. Macromodel included in this specification. D SO-14 (Plastic Micropackage) N DIP14 (Plastic Package)
Description
The TS514 is a high-performance quad operational amplifier with frequency and phase compensation built into the chip. The internal phase compensation allows stable operation as a voltage follower in spite of its high gain-bandwidth product. The circuit presents very stable electrical characteristics over the entire supply voltage range, and is particularly intended for professional and telecom applications (active filter, etc.).
Pin Connections (top view)
Output 1 Inverting Input 1 Non-inverting Input 1 V CC + Non-inverting Input 2 Inverting Input 2 Output 2 1 2 3 4 5 6 7 + + + + 14 Output 4 13 Inverting Input 4 12 Non-inverting Input 4 11 VCC 10 Non-inverting Input 3 9 8 Inverting Input 3 Output 3
Order Codes
Part Number TS514IN TS514AIN TS514ID/IDT TS514AID/AIDT TS514IYD/IYDT TS514AIYD/AIYDT Temperature Range Package DIP14 -40, + 125C SO-14 SO14 (automotive grade level) Packing Tube Tube or Tape & Reel Marking 514IN 514AIN 514I 514AI 514IY 514AIY
September 2005
Rev. 3 1/10
www.st.com
10
Absolute Maximum Ratings
TS514 / TS514A
1
Absolute Maximum Ratings
Table 1.
Symbol VCC Vi Vid(1) ptot Tstg Rthja Supply Voltage Input Voltage Positive Negative Differential Input Voltage Power Dissipation at Tamb = 70C (2) Storage Temperature Range Thermal Resistance Junction to Ambient SO14 DIP14 HBM: Human Body Model(3) ESD MM: Machine Model(4) CDM: Charged Device Model
1. Differential voltages are with respect to the midpoint between Vcc+ and Vcc-. 2. Power dissipation must be considered to ensure maximum junction temperature (Tj) is not exceeded. 3. Human body model, 100pF discharged through a 1.5k resistor into pin of device. 4. Machine model ESD, a 200pF cap is charged to the specified voltage, then discharged directly into the IC with no external series resistor (internal resistor < 5), into pin to pin of device.
Key parameters and their absolute maximum ratings
Parameter Value 18 +VCC -Vcc - 0.5 (VCC - 1) 400 -65 to +150 Unit V V
V mW C
103 66 2 <200 1.5
C/W
kV V kV
Table 2.
Symbol VCC+
Operating conditions
Parameter Min +3 Supply voltage -3 Operating Free Air Temperature Range -40 Max +15 V -15 +125 C Unit
VCCToper
2/10
TS514 / TS514A
Schematic Diagram
2
Schematic Diagram
Figure 1. Typical application schematic for 1/4 of the TS514
3/10
Electrical Characteristics
TS514 / TS514A
3
Electrical Characteristics
Table 3.
Symbol Icc Iib Ri Supply Current Input Bias Current - at 25C - at T min Top Tmax Input Resistance, f = 1kHz Input Offset Voltage - at 25C: Vio TS514 TS514A - at T min Top T max TS514 TS514A Input Offset Voltage Drift at Tmin T op Tmax Input Offset Current Iio at 25C at T min Top Tmax Input Offset Current Drift Tmin Top Tmax Output Short Circuit Current Large Signal Voltage Gain, RL = 2k Avd GBP Vcc = 15V Vcc = 4V Gain-bandwidth Product, f = 100kHz Equivalent Input Noise Voltage, f = 1kHz en Rs = 50 Rs = 1k Rs = 10k Total Harmonic Distortion Av = 20dB, RL = 2k Vo = 2V pp, f = 1kHz , Output Voltage Swing, R L = 2k Vopp Vopp SR CMR SVR Vcc = 15V Vcc = 4V Large Signal Voltage Swing, RL = 10k, f = 10kHz Slew Rate, unity gain, RL = 2k Common Mode Rejection Ratio, Vic = 10V Supply Voltage Rejection Ratio, dVic = 10V, f = 100Hz 0.8 90 90 120 13 3 28 1.5 Vpp V/s dB dB dB V 8 10 18 0.03 15 nV ----------Hz 90 1.8 100 95 3 dB 5 20 40 nA 0.5 2.5 0.5 4 1.5 5 V/C mV
VCC = 15V, Tamb = 25C (unless otherwise specified)
Parameter Min. Typ. 1.4 Max. 2.4 Unit mA
50
150 300
nA
1
M
Vio
Iio Ios
0.08 23
nA ------C mA
MHz
THD
0.1
%
Vo1/Vo2 Channel Separation, f = 1kHz
4/10
TS514 / TS514A
Macromodels
4
4.1
Macromodels
Important note concerning this macromodel
Please consider following remarks before using this macromodel.

All models are a trade-off between accuracy and complexity (i.e. simulation time). Macromodels are not a substitute to breadboarding; rather, they confirm the validity of a design approach and help to select surrounding component values. A macromodel emulates the NOMINAL performance of a TYPICAL device within SPECIFIED OPERATING CONDITIONS (i.e. temperature, supply voltage, etc.). Thus the macromodel is often not as exhaustive as the datasheet, its goal is to illustrate the main parameters of the product. Data issued from macromodels used outside of its specified conditions (Vcc, Temperature, etc.) or even worse: outside of the device operating conditions (Vcc, Vicm, etc.) are not reliable in any way.
In Section 4.2, the electrical characteristics resulting from the use of this macromodel are presented.
4.2
Electrical characteristics from macromodelization
Table 4. Electrical characteristics resulting from macromodel simulation at V cc = 15V, Tamb = 25C (unless otherwise specified)
Conditions Value 0 RL = 2k No load, per operator 94 325 -13.5 to 13.5 RL = 2k RL = 2k Vo = 0V Vo = 0V RL = 2k, CL = 100pF RL = 2k, CL = 100pF RL = 2k, CL = 100pF +13 -13 24 24 3 1.4 55 Unit mV V/mV A V V V mA mA MHz V/s Degrees
Symbol Vio Avd Icc Vicm VOH VOL Isink Isource GBP SR m
5/10
Macromodels
TS514 / TS514A
4.3
Macromodel code
** Standard Linear Ics Macromodels, 1993. ** CONNECTIONS : * 1 INVERTING INPUT * 2 NON-INVERTING INPUT * 3 OUTPUT * 4 POSITIVE POWER SUPPLY * 5 NEGATIVE POWER SUPPLY .SUBCKT TS514 1 3 2 4 5 (analog) ******************************************************** .MODEL MDTH D IS=1E-8 KF=6.647807E-16 CJO=10F * INPUT STAGE CIP 2 5 1.000000E-12 CIN 1 5 1.000000E-12 EIP 10 5 2 5 1 EIN 16 5 1 5 1 RIP 10 11 1.300000E+01 RIN 15 16 1.300000E+01 RIS 11 15 6.437882E+01 DIP 11 12 MDTH 400E-12 DIN 15 14 MDTH 400E-12 VOFP 12 13 DC 0 VOFN 13 14 DC 0 IPOL 13 5 2.000000E-05 CPS 11 15 9.75E-10 DINN 17 13 MDTH 400E-12 VIN 17 5 0.000000e+00 DINR 15 18 MDTH 400E-12 VIP 4 18 1.500000E+00 FCP 4 5 VOFP 1.525000E+01 FCN 5 4 VOFN 1.525000E+01 FIBP 2 5 VOFN 5.000000E-03 FIBN 5 1 VOFP 5.000000E-03 * AMPLIFYING STAGE FIP 5 19 VOFP 1.125000E+03 FIN 5 19 VOFN 1.125000E+03 RG1 19 5 6.512062E+05 RG2 19 4 6.512062E+05 CC 19 29 1.500000E-08 HZTP 30 29 VOFP 8.944787E+02 HZTN 5 30 VOFN 8.944787E+02 DOPM 19 22 MDTH 400E-12 DONM 21 19 MDTH 400E-12 HOPM 22 28 VOUT 6.521739E+03 VIPM 28 4 1.500000E+02 HONM 21 27 VOUT 6.521739E+03 VINM 5 27 1.500000E+02 GCOMP 5 4 4 5 7.485029E-04 RPM1 5 80 1E+09 RPM2 4 80 1E+09
6/10
TS514 / TS514A
GAVPH 5 82 19 80 2.99E-03 RAVPHGH 82 4 668 RAVPHGB 82 5 668 RAVPHDH 82 83 1000 RAVPHDB 82 84 1000 CAVPHH 4 83 0.352E-09 CAVPHB 5 84 0.352E-09 EOUT 26 23 82 5 1 VOUT 23 5 0 ROUT 26 3 150 COUT 3 5 1.000000E-12 DOP 19 25 MDTH 400E-12 VOP 4 25 1.785252E+00 DON 24 19 MDTH 400E-12 VON 24 5 1.785252E+00 .ENDS
Macromodels
7/10
Package Mechanical Data
TS514 / TS514A
5
Package Mechanical Data
In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com.
5.1
DIP14 Package
Plastic DIP-14 MECHANICAL DATA
mm. DIM. MIN. a1 B b b1 D E e e3 F I L Z 1.27 3.3 2.54 0.050 8.5 2.54 15.24 7.1 5.1 0.130 0.100 0.51 1.39 0.5 0.25 20 0.335 0.100 0.600 0.280 0.201 1.65 TYP MAX. MIN. 0.020 0.055 0.020 0.010 0.787 0.065 TYP. MAX. inch
P001A
8/10
TS514 / TS514A
Package Mechanical Data
5.2
SO-14 Package
SO-14 MECHANICAL DATA
DIM. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 8.55 5.8 1.27 7.62 4.0 5.3 1.27 0.68 8 (max.) 0.149 0.181 0.019 8.75 6.2 0.35 0.19 0.5 45 (typ.) 0.336 0.228 0.050 0.300 0.157 0.208 0.050 0.026 0.344 0.244 0.1 mm. MIN. TYP MAX. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.003 MIN. inch TYP. MAX. 0.068 0.007 0.064 0.018 0.010
PO13G
9/10
Revision History
TS514 / TS514A
6
Revision History
Date March 2001 June 2005 Revision 1 2 Initial release Automotive grade part references inserted in the datasheet (see Order Codes on page 1). The following changes were made in this revision: - An error in the device description was corrected on page 1. - Order Codes on page 1 updated with complete list of markings. - Addition of supplementary data in Table 1: Key parameters and their absolute maximum ratings on page 2. - Addition of Table 2: Operating conditions on page 2. - Reorganization of Chapter 4: Macromodels on page 5. - Minor grammatical and formatting changes throughout. Changes
Sept. 2005
3
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners (c) 2005 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
10/10

▲Up To Search▲

Price & Availability of TS51405

	To Download TS51405 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .